Showing content from https://crankyoldgit.github.io/IRremoteESP8266/doxygen/html/classIRDaikin176.html below:
IRremoteESP8266: IRDaikin176 Class Reference
Class for handling detailed Daikin 176-bit A/C messages. More...
#include <ir_Daikin.h>
void stateReset (void) Reset the internal state to a fixed known good state. More...
void checksum (void) Calculate and set the checksum values for the internal state. More...
Class for handling detailed Daikin 176-bit A/C messages.
◆ IRDaikin176() IRDaikin176::IRDaikin176 ( const uint16_t pin, const bool inverted = false, const bool use_modulation = true ) explicit
Class constructor.
-
Parameters
-
[in] pin GPIO to be used when sending. [in] inverted Is the output signal to be inverted? [in] use_modulation Is frequency modulation to be used?
◆ begin() void IRDaikin176::begin ( void )
Set up hardware to be able to send a message.
◆ calibrate() int8_t IRDaikin176::calibrate ( void ) inline
Run the calibration to calculate uSec timing offsets for this platform.
-
Returns
-
The uSec timing offset needed per modulation of the IR Led.
-
Note
-
This will produce a 65ms IR signal pulse at 38kHz. Only ever needs to be run once per object instantiation, if at all.
◆ checksum() void IRDaikin176::checksum ( void ) private
Calculate and set the checksum values for the internal state.
◆ convertFan()
Convert a stdAc::fanspeed_t enum into it's native speed.
-
Parameters
-
[in] speed The enum to be converted.
-
Returns
-
The native equivalent of the enum.
◆ convertMode()
Convert a stdAc::opmode_t enum into its native mode.
-
Parameters
-
[in] mode The enum to be converted.
-
Returns
-
The native equivalent of the enum.
◆ convertSwingH()
Convert a stdAc::swingh_t enum into it's native setting.
-
Parameters
-
[in] position The enum to be converted.
-
Returns
-
The native equivalent of the enum.
◆ getFan() uint8_t IRDaikin176::getFan ( void ) const
Get the current fan speed setting.
-
Returns
-
The current fan speed.
◆ getId() uint8_t IRDaikin176::getId ( void ) const
Get the Unit Id of the A/C.
-
Returns
-
The Unit Id the A/C is to use.
◆ getMode() uint8_t IRDaikin176::getMode ( void ) const
Get the operating mode setting of the A/C.
-
Returns
-
The current operating mode setting.
◆ getPower() bool IRDaikin176::getPower ( void ) const
Get the value of the current power setting.
-
Returns
-
true, the setting is on. false, the setting is off.
◆ getRaw() uint8_t * IRDaikin176::getRaw ( void )
Get a PTR to the internal state/code for this protocol.
-
Returns
-
PTR to a code for this protocol based on the current internal state.
◆ getSwingHorizontal() uint8_t IRDaikin176::getSwingHorizontal ( void ) const
Get the Horizontal Swing mode of the A/C.
-
Returns
-
The native position/mode setting.
◆ getTemp() uint8_t IRDaikin176::getTemp ( void ) const
Get the current temperature setting.
-
Returns
-
The current setting for temp. in degrees celsius.
◆ off() void IRDaikin176::off ( void )
Change the power setting to Off..
◆ on() void IRDaikin176::on ( void )
Change the power setting to On.
◆ send()
Send the current internal state as an IR message.
-
Parameters
-
[in] repeat Nr. of times the message will be repeated.
◆ setFan() void IRDaikin176::setFan ( const uint8_t fan )
Set the speed of the fan.
-
Parameters
-
[in] fan The desired setting.
-
Note
-
1 for Min or 3 for Max
◆ setId() void IRDaikin176::setId ( const uint8_t num )
Set the Unit Id of the A/C.
-
Parameters
-
[in] num The Unit Id the A/C is to use.
-
Note
-
0 for Unit A; 1 for Unit B
◆ setMode() void IRDaikin176::setMode ( const uint8_t mode )
Set the operating mode of the A/C.
-
Parameters
-
[in] mode The desired operating mode.
◆ setPower() void IRDaikin176::setPower ( const bool on )
Change the power setting.
-
Parameters
-
[in] on true, the setting is on. false, the setting is off.
◆ setRaw() void IRDaikin176::setRaw ( const uint8_t new_code[] )
Set the internal state from a valid code for this protocol.
-
Parameters
-
[in] new_code A valid code for this protocol.
◆ setSwingHorizontal() void IRDaikin176::setSwingHorizontal ( const uint8_t position )
Set the Horizontal Swing mode of the A/C.
-
Parameters
-
[in] position The position/mode to set the swing to.
◆ setTemp() void IRDaikin176::setTemp ( const uint8_t temp )
Set the temperature.
-
Parameters
-
[in] temp The temperature in degrees celsius.
◆ stateReset() void IRDaikin176::stateReset ( void ) private
Reset the internal state to a fixed known good state.
◆ toCommon()
Convert the current internal state into its stdAc::state_t equivalent.
-
Returns
-
The stdAc equivalent of the native settings.
◆ toCommonFanSpeed()
Convert a native fan speed into its stdAc equivalent.
-
Parameters
-
[in] speed The native setting to be converted.
-
Returns
-
The stdAc equivalent of the native setting.
◆ toCommonMode()
Convert a native mode into its stdAc equivalent.
-
Parameters
-
[in] mode The native setting to be converted.
-
Returns
-
The stdAc equivalent of the native setting.
◆ toCommonSwingH()
Convert a native horizontal swing postion to it's common equivalent.
-
Parameters
-
[in] setting A native position to convert.
-
Returns
-
The common horizontal swing position.
◆ toString() String IRDaikin176::toString ( void ) const
Convert the current internal state into a human readable string.
-
Returns
-
A human readable string.
◆ validChecksum()
Verify the checksum is valid for a given state.
-
Parameters
-
[in] state The array to verify the checksum of. [in] length The length of the state array.
-
Returns
-
true, if the state has a valid checksum. Otherwise, false.
◆ _ ◆ _irsend
instance of the IR send class
◆ _saved_temp uint8_t IRDaikin176::_saved_temp private
The previously user requested temp value.
The documentation for this class was generated from the following files:
RetroSearch is an open source project built by @garambo
| Open a GitHub Issue
Search and Browse the WWW like it's 1997 | Search results from DuckDuckGo
HTML:
3.2
| Encoding:
UTF-8
| Version:
0.7.4